NuPool Epoxy
2 Pack Epoxy Coating
NuPool Epoxy is an isocyanate-free, high build gloss epoxy coating that is impervious to water and moisture. Formulated specifically for new bare concrete and fibreglass pools and recoating of aged 2 pack epoxy coated concrete and fibreglass swimming pools. NuPool Epoxy provides excellent resistance to scuffing, abrasion as well as protection against fatty oils, alkali, acid and efflorescence. It is available in 13 standard colours.
NuPool Epoxy Features
Isocyanate Free
Excellent adhesion
Excellent hardness
Outstanding chemical resistance
Hard-wearing
High resistance to corrosion and abrasion
Will resist bacterial growth
Easy application by brush, roller or spray
 
Application Guide
Equipment & Tools
Brush or Roller (see TDS for spray application)
Pressure washer and vacuum cleaner
Drop sheets, cardboard or old tarps
Preparation
Drain the pool using a portable high volume pump, and ensure that all pool equipment is turned off and unplugged.
Degrease the entire pool with Nu-EcoSafe Degreaser
Pressure clean the entire pool with a >2000psi pressure washer
Ensure all stains, oil and the chemical residue is removed. Repeat the cleaning process if needed
For bare concrete, etch the surface using Nu-EcoSafe Etch and rinse well
For old or existing 2 pack epoxy surfaces, sand or abrade the entire surface
Remove all flaking and peeling paint by water blasting or using mechanical abrasion.
Make any spot repairs to cracks or chips
Vacuum the entire pool with a soft bristle head. Ensure that all debris has been removed
Create a safe mixing area near the pool with drop sheets, tarps or cardboard
Ensure the surface is completely dry before continuing.
Vacuum the entire pool with a soft bristle head, ensuring that all debris has been removed.
Coat One
Mix the first coat of NuPool Epoxy using the 3:1 ratio (2-part kit) by adding NuPool Epoxy Part B into NuPool Epoxy Part A
Mix the 2 parts together thoroughly using a drill mixer
Add EPiC Epoxy 500 Thinner (approx 20%) and mix again
Allow the paint to stand for 10 minutes before application
Use a brush to cut in all edges and corners with NuPool, then roll to cover the surface
Allow drying for 5 hours (temperature dependant), before applying the second coat
DO NOT wait more than 72 hours before applying a second coat
Coat Two
Mix the second coat of NuPool Epoxy using the 3:1 ratio (2-part kit) by adding NuPool Part B into NuPool Part A
Mix the 2 parts together thoroughly using a drill mixer
Allow the paint to stand for 10 minutes before application
Use a brush to cut in all edges and corners with NuPool Epoxy, then roll to cover the surface
Allow drying for 5 hours (temperature dependant)
Non-Slip
To create a non-slip surface, apply Nutech Coarse Anti-Slip to the second coat while it is still wet
If anti-slip has been applied, use a third coat of NuPool Epoxy over the areas
Curing
NuPool Epoxy takes 7 days to completely cure into a hard and durable surface. During this time, the pool must be kept dry. If the surface becomes wet, remove all water and allow it to continue curing
The paint will cover approximately 6-8 m2/L. Minimum 2 coats required.  
Average pool 50,000 - 60,000 litres will require approximately 5-7 x 4L kits for a two coat finish.
Coverage : 6 - 8 m2/L
Comes in 4L, 10L & 20L kit
 
Technical Data Sheet 
 
Colour Disclaimer:
These colours are a guide to the range produced with the 36 standard colours of Nutech Paint. The colours shown are as close as possible to the actual colour of the paint. The paint itself will appear darker on large areas and shade variations may occur from product to product or as the gloss level is varied.
When selecting colours, please confirm that your choice is available in a coating that meets the performance specifications for your application. When colour matching to precise colours is necessary, reference should be made to a colour sample.